DN100 2PC Stainless Steel Flanged Ball Valve with PTFE Sealing
산업 소싱용
명확한 RFQ 준비
RELIA가 부품을 이해하고 다음 단계를 논의할 수 있도록 아래 정보를 포함하세요.
- 도면, 샘플 또는 참고 표준
- 재질 등급 및 선호 공정
- 치수, 공차 및 표면 처리
- 용도, 목표 수량 및 목적지
생산 일정, 포장 및 운송 조건은 사양과 거래 조건 합의 후 프로젝트별로 확정됩니다.
-
applicationGeneralBall MaterialSTAINLESS STEEL
-
Connection TypeflangemediaBASE
-
Port Size1/4in - 4instructureBall
-
model numberball valveConnection Size1/4in - 4in
-
customized supportOEM, odmFlow Rate0-100L/min
-
For Maximum Pipe Size4in(10.16cm)Operating PressureLow Pressure
-
Operating Temp. Range0~150 Celsiuspowermanual
-
Sealing MaterialPTFEtemperature of mediaMedium Temperature
-
warranty1 year
This DN100 2PC stainless steel flanged ball valve enquiry requires a confirmed supplied size before installation planning. PTFE sealing and a flanged connection describe the requested arrangement; an accepted assembly drawing should establish the valve actually offered.
Confirm supplied size and flange assembly
Sixteen actual variants combine Stainless Steel or Casting, Low Pressure or Medium Pressure, and four sizes: 3/8 in, 1/2 in, 3/4 in and 1 in(2.54cm). Obtain confirmation of the delivered nominal size. The broad port/connection range and maximum pipe entry cannot establish a selectable DN100 valve.
Check actual bore, flange outside diameter, facing, drilling and face-to-face length against the mating pipe system. Confirm the requested two-piece body construction on the assembly drawing. The two viewed blue flanged valve photos show handwheel arrangements but cannot establish supplied size, manufacturer, construction details or rated capacity.
Identify wetted components and PTFE sealing
The stainless Ball Material entry concerns the ball; it does not certify body or stem grades. Casting identifies a production route rather than chemistry. Specify exact component materials, traceability and inspection evidence for the chosen valve, including all wetted parts.
Confirm the PTFE compound, seat design and leakage acceptance for the actual medium. Water, oil, gas and BASE wording does not establish universal compatibility. Provide fluid composition, concentration and contaminants rather than treating BASE as an accepted chemical-service claim.
Validate operation and the combined duty
Low Pressure and Medium Pressure labels provide no numerical operating limits. The stated temperature and flow ranges also require selection-specific pressure-temperature and performance evidence. Define shutoff or control duty, cycling, required flow and any throttling requirements before accepting suitability.
For manual operation, verify the mechanism, operating torque, access and clearances. Submit the supplied size/interface drawing, component certificates, seal requirements and complete medium, pressure, temperature and flow conditions together for technical acceptance.
모든 제품 문의에 필요한 기술 정보
최종 제품 확정 전에 요구사항을 준비하세요.
제품 페이지는 출발점입니다. 재고 매칭 또는 맞춤 생산 확정 전에 도면, 샘플, 인터페이스, 소재, 수량, 검수 요구사항을 검토합니다.
프로젝트 상황에 맞춰 이 제품을 상담하세요.
도면, 샘플, 참조품, 목표 수량, 용도 정보를 공유하세요. 미확정 항목은 검토 상태로 둘 수 있습니다.
